Kenwood eXcelon KDC X689 User Manual

CD-RECEIVER

KDC-X689

INSTRUCTION MANUAL

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best

performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the

warranty card, and in the space provided below. Refer to the model and serial numbers

whenever you call upon your Kenwood dealer for information or service on the product.

Model KDC-X689 Serial number

US Residence Only

www.kenwoodusa.com

Basic Operations of remote control 36

Accessories/ Installation Procedure 39

Connecting Wires to Terminals

Installation

Removing the Unit

Troubleshooting Guide

Specifications

The "AAC" logo is trademark of Dolby

Laboratories.

English

Safety precautions

About CD players/disc changers

connected to this unit

Kenwood disc changers/ CD players released in

1998 or later can be connected to this unit.

Refer to the catalog or consult your Kenwood

dealer for connectable models of disc changers/

CD players.

2WARNING

To prevent injury or fire, take the

following precautions:

• To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools)

inside the unit.

Note that any Kenwood disc changers/ CD players

released in 1997 or earlier and disc changers made

by other makers cannot be connected to this unit.

Connecting unsupported disc changers/CD players

to this unit may result in damage.

Set the "O-N" Switch to the "N" position for the

applicable Kenwood disc changers/ CD players.

The functions you can use and the information

that can be displayed may differ depending on the

models being connected.

2CAUTION

To prevent damage to the machine, take

the following precautions:

• Make sure to ground the unit to a negative 12V

DC power supply.

• Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of

water splashing.

• Do not place the faceplate or the faceplate case in

areas exposed to direct sunlight, excessive heat or

humidity. Also avoid places with too much dust or

the possibility of water splashing.

• To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

•

You can damage both your unit and the CD changer if

you connect them incorrectly.

LX-bus connection

The LX AMP and the sensor unit must be connected

one at a time.

• Do not subject the faceplate to excessive shock,

as it is a piece of precision equipment.

• When replacing a fuse, only use a new fuse with

the prescribed rating. Using a fuse with the wrong

rating may cause your unit to malfunction.

• Do not apply excessive force to the open

faceplate or place objects on it. Doing so will

cause damage or breakdown.

• Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

Lens Fogging

When you turn on the car heater in cold weather,

dew or condensation may form on the lens in the

CD player of the unit. Called lens fogging, this

condesnation on the lens may not allow CDs to

play. In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit still

does not operate normally after a while, consult

your Kenwood dealer.

Faceplate

Attach the panel while you are on the

vehicle

The panel lock arm appears when the panel is

removed. Therefore, the panel must be attached

while the electrical system of the car is operating.

• Use the enclosed or dedicated faceplate. Using a

faceplate other than the specified one may cause

your unit to malfunction.

Do Not Load 3-in. CDs in the CD slot

If you try to load a 3 in. CD with its adapter into the

unit, the adapter might separate from the CD and

damage the unit.

NOTE

This Class B digital apparatus complies with

Canadian ICES-003.

English

Notes

• If you experience problems during installation,

consult your Kenwood dealer.

• If the unit fails to operate properly, press the Reset

button to restore factory settings.

Before using this unit for the first time

This unit is initially set on the Demonstration mode.

When using this unit for the first time, cancel the

<Demonstration mode Setting> (page 35).

• Press the reset button if the disc auto changer fails

to operate correctly. Normal operation should be

restored.

About SIRIUS Satellite radio tuner

Refer to the instruction manual of SIRIUS Satellite

radio tuner KTC-SR901/SR902/SR903 (optional

accessory) when connected, for the operation

method.

• Refer to the sections of A models for operations.

FM/SCRL

Reset button

• We recommend the use of <Security Code>

(page 30) to prevent theft.

• The characters conforming to ISO 8859-1

character set can be displayed.

• There are places in this manual where lit

indicators are described; however, the only time

an indicator will light is in the following settings.

When Indicator is selected as mentioned in <Text

Display Switching> (page 15)

AUTO

1 — 6

38 SRC

• The illustrations of the display and the panel

appearing in this manual are examples used to

explain more clearly how the controls are used.

Therefore, what appears on the display in the

illustrations may differ from what appears on the

display on the actual equipment, and some of the

illustrations on the display may be inapplicable.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a

dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain off

with a cloth moistened with neutral cleaner, then

wipe it again with a clean soft dry cloth.

•

Applying spray cleaner directly to the unit may affect its

mechanical parts. Wiping the faceplate with a hard cloth

or using a volatile liquid such as thinner or alcohol may

scratch the surface or erases characters.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get dirty,

wipe them with a clean soft dry cloth.

English

Notes

2Warning

About DAB Tuner control

2CAUTION

Refer to A group on the Instruction manual of DAB

Tuner KTC-9090DAB (optional accessory) for the

control method of DAB Tuner function.

However, the following control methods of the

function for this unit may be differed from the

Instruction manual; therefore, refer to the following

supplemental instruction.

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

In compliance with Federal Regulations, following

are reproductions of labels on, or inside the product

relating to laser product safety.

kenwood CORPORATION

2967-3, ISHIKAWA-MACHI,

HACHIOJI-SHI

1. Select the preset band for Auto Ensemble

Memory Entry.

TOKYO, JAPAN

2. Press the [AME] button for at least 2 seconds.

Open Auto Ensemble Memory Entry.

After storing in the memory finishes, the

number of the pre-set buttons and the

ensemble label are displayed.

kenwood CORP. CERTIFIES THIS EQUIPMENT

CONFORMS TO DHHS REGULATIONS N0.21 CFR

1040. 10, CHAPTER 1, SUBCHAPTER J.

and <Languages to be displayed> in

Location : Bottom Panel

At the operation to press [DISP] button, press

[AUTO] button.

FCC WARNING

This equipment may generate or use radio

frequency energy. Changes or modifications to

this equipment may cause harmful interference

unless the modifications are expressly approved

in the instruction manual. The user could lose

the authority to operate this equipment if an

unauthorized change or modification is made.

About "Media Manager" of PC application

attached to KDC-X689

• "Media Manager" is recorded in the CD-ROM

attached to this unit.

• Refer to the attached installation manual for the

installation method of "Media Manager".

• Refer to the user’s manual recorded in the

installation CD-ROM and Help of "Media Manager"

for the operation method of "Media Manager".

• The unit can play CD (hereafter called "ACDrive

disc") created by "Media Manager".

• Refer to the following site for the updated

information of "Media Manager".

http://www.kenwood.mediamanager.jp

• Contact Kenwood for the function and operation

of the "Media Manager".

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment may cause harmful

interference to radio communications, if it is

not installed and used in accordance with the

instructions. However, there is no guarantee

that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which

can be determined by turning the equipment off

and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• "Media Manager" is a product of PhatNoise.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

English

About CDs

Handling CDs

• Do not touch the recording surface of the CD.

Removing CDs

When removing CDs from this unit pull them out

horizontally.

CDs that cannot be used

• CDs that are not round cannot be used.

• CD-R and CD-RW are easier to damage than a

normal music CD. Use a CD-R or a CD-RW after

reading the caution items on the package etc.

• Do not stick tape etc. on the CD, or use a CD with

tape stuck on it.

• CDs with coloring on the recording surface or CDs

that are dirty cannot be used.

• This unit can only play the CDs with

When using a new CD

If the CD center hole or outside rim has burrs,

use the CD only after removing the burrs with a

ballpoint pen etc.

This unit may not correctly play discs which do

not have the mark.

• You cannot play A CD-R or CD-RW that has not

been finalized. (For the finalization process refer to

your CD-R/CD-RW writing software, and your CD-

R/CD-RW recorder instruction manual.)

Burrs

CD storage

Burrs

• Do not place CDs in direct sunlight (On the seat

or dashboard etc.) or where the temperature is

high.

• Store CDs in their cases.

CD accessories

Do not use disc type accessories.

CD cleaning

Clean from the center of the disc and move

outward.

English

About AAC, MP3 and WMA

The playable AAC/MP3/WMA file (hereafter called

Audio file) and the media format has the following

limitation. The Audio file, which is not comforming

to the specification, may not play normally, or the

file and folder names may not display correctly.

The maximum number of characters for

display

File/Folder name: 128 characters

MP3 ID3 Tag/ WMA Contents property:

30 characters

AAC song information: 60 characters

•

Attach the correct extension for the Audio file

(AAC: ".M4A", MP3: ".MP3", WMA: ".WMA")

Do not attach the extensions to files other than the

Audio file. If the extension is attached, the file, which is

not the Audio file, will play and outputs a loud noise,

causing damage to the speaker.

•

File/Folder name is the number of the characters

including the extensions

AAC ID3 Tag cannot be displayed.

Limitation of structure for the file and the

folder

• Maximum number of directory levels: 8

• Maximum number of folders: 100

• Maximum number of files per folder: 4096

•

The files with copy protection cannot be played.

Playable AAC file

• ".m4a" file encoded by AAC-LC format.

Refer to http://www.kenwood.mediamanager.jp

for the details.

Playing order of the Audio file

The Audio file plays in the order which is written by

writing software. You may be able to set the playing

order by writing the play sequence numbers such

as "01" to "99" at the beginning of the file name.

Playable MP3 file

• MPEG 1/2 Audio Layer 3 file

• Transfer bit rate: 8-320 kbps

• Sampling frequency

Example

: 16, 22.05, 24, 32, 44.1, 48 kHz

: Folder

: Audio file

(1)

Playable WMA file

• The file in accordance with Windows Media Audio

(Except for the file for Windows Media Player 9 or

after which applies the new functions)

¡!

¡"

• Transfer bit rate: 48-192 kbps

• Sampling frequency: 32, 44.1, 48 kHz

¡#

¡$

Playable media

• CD-ROM, CD-R, CD-RW

¡%

•

CD-RW discs which are quick formatted by the writing

software cannot be used.

When recording to the maximum media capacity at

once, the writing software is set to "Disc at once".

• Playing order

Playing order after ¡! play.

➡ ¡", ¡#, ¡$, ¡%...

• File search

Playable disc format

Forward file search during ¡# play.

Push the Control knob towards [¢] ➡ ¡$

• Folder search

Forward folder search during ¡" play.

Push the Control knob towards [FM] ➡ 3, 4...

• ISO 9660 Level 1/2

• Joliet

• Romeo

• Long file name.

• Folder select

When the selection is set to directory 4, and you

want to skip to the folder 2 at the same level.

Push the Control knob towards [4] ➡ 2

When the selection is set to directory 3, moves

the level up by folder select.

Push the Control knob towards [AM] ➡ 2

English

General features

ATT

ANG

VOL

Q/MENU

SRC

Control knob

FM1-6ch 98.1

12:34

01-Jan-05 Sat

Power

Hiding the Control Panel

Prevents tampering with the unit while your car is

being serviced etc.

Turning ON the Power

Turn the vehicle ignition ON.

The control panel appears.

Hiding the control panel

Press the [SRC] button for at least 1 second.

When the time set in <OFF Wait Time Setting>

(page 31) lapses, the panel is hidden and the

power turns OFF.

Turing OFF the Power

Turn the vehicle ignition OFF or press the

[SRC] button for at least 1 second.

The control panel is hidden.

Showing the control panel

Press the lower left part of the panel.

•

Do not apply force to the control panel during this

operation. It can cause damage.

The panel opens to enable the operation.

English

General features

Selecting the Source

Sound setting

User memory

Rock

Pops

Easy

Display

"User"

"Rock"

"Pops"

"Easy"

Press the [SRC] button.

Source required

SIRIUS tuner (Optional accessory)

Display

"SIRIUS"

Top 40

Jazz

Natural

"Top 40"

"Jazz"

"Natural"

Tuner or HD Radio (Optional accessory) "TUNER" or "HD RADIO"

"Compact Disc"

"CD Changer"

"AUX"

External disc (Optional accessory)

Auxiliary input

Auxiliary input (Optional accessory)

Standby (Illumination only mode)

"AUX EXT"

"STANDBY"

•

User memory: The values set on the <Audio Control>

(page 11).

Change each setting value with the <Speaker

Setting> (page 10).

First, select the speaker type with the Speaker setting.

Volume

Increasing Volume

Turn the [VOL] knob clockwise.

Speaker Setting

Decreasing Volume

Turn the [VOL] knob counterclockwise.

Fine-tuning so that the System Q value is optimal

when setting the speaker type.

1 Enter Standby

Press the [SRC] button.

Select the "STANDBY" display.

Attenuator

Turning the volume down quickly.

2 Enter Speaker Setting mode

Press the [VOL] knob.

Press the [ATT] button.

Each time you press the button is pressed, the

Attenuator turns ON and OFF.

When the Attenuator is ON, "ATT ON" is

displayed.

3 Select the Speaker type

Turn the [VOL] knob.

Each time you turn the knob, the setting

alternates between the settings shown in the

table below.

Speaker type

OFF

For 5 & 4 in. speaker

For 6 & 6x9 in. speaker

For the OEM speaker

Display

"Speaker OFF"

"Speaker 5/4inch"

"Speaker 6x9/6inch"

"Speaker O.E.M."

System Q

Selecting the best sound setting preset for

different types of music.

1 Select the source to set

Press the [SRC] button.

4 Exit Speaker Setting mode

Press the [VOL] knob.

2 Select the Sound type

Press the [Q] button.

Each time you press the button is pressed, the

sound setting alternates.

English

3 Select the Detail Audio item to adjust

Press the [VOL] knob.

Audio Control

Each time you press the knob, the item to be

adjusted alternates between the items shown

in the table below.

4 Adjust the Detail Audio item

Turn the [VOL] knob.

1 Select the source to adjust

Press the [SRC] button.

2 Enter Audio Control mode

Press the [VOL] knob.

3 Select the Basic Audio item to adjust

Press the [VOL] knob.

Each time you press the knob, the item to be

adjusted alternates between the items shown in

the table below.

Bass level

Adjustment Item

Bass Center Frequency "Bass Freq" 40/50/60/70/80/100/

120/150 Hz

Bass Q Factor

Bass Extend

Display

Range

"Bass Q"

"Bass EXT" ON/OFF

1.00/1.25/1.50/2.00

4 Adjust the Basic Audio item

Turn the [VOL] knob.

Middle level

Adjustment Item Display

Rear Volume *¹

"R-Volume"

Range

0 — 35

Adjustment Item

Middle Center Frequency "Middle Freq" 0.5/1.0/1.5/2.0 kHz

Middle Q Factor

Display

Range

Subwoofer level*^2,3"SW_Level" –15 — +15

"Middle Q" 1.0/2.0

Bass level*⁴

"Bass Level"

–8 — +8

Treble level

Middle level*⁴

Treble level*⁴

Balance

"Middle Level" –8 — +8

"Treble Level" –8 — +8

Adjustment Item

Treble Center Frequency "Treble Freq" 10.0/12.5/15.0/17.5 kHz

Display

Range

"Balance"

"Fader"

Left 15 — Right 15

Rear 15 — Front 15

Fader*³

5 Exit the Detail Audio Control mode

Exit Audio Control mode

Press the [VOL] knob for at least 1 second.

•

When you set the Bass Extend to ON, low frequency

response is extended by 20%.

You can exit the Audio Control mode at anytime by

pressing any button except for [VOL], [ANG] and [ATT]

buttons.

•

*¹You can control this item when "2Zone" of <Audio

Setup> (page 12) is set to "ON".

*³You can control this item when <Subwoofer

Output> (page 12) is set to "SW ON".

*³You can control this item when "2Zone" of <Audio

Setup> (page 12) is set to "OFF".

*⁴You can adjust these items in detail by the following

methods.

*⁴Source tone memory: Puts the set up value in the

memory per source. (Detail Audio item is included)

5 Exit Audio Control mode

Press any button.

Press a button other than the [VOL] knob and

[ATT]/ [ANG] button.

Adjust the detail of Audio Control

1 Select the Audio item to adjust

By referring to the step 1 — 3 above, select the

desired item to be set in detail from the items

marked with *⁴.

2 Enter Detail adjustment mode of Audio

Control

Press the [VOL] knob for at least 1 second.

English

General features

•

You can use the Dual Zone System with the Auxiliary

input sources listed below.

Audio Setup

Setting the Sound system, such as Cross over

Network.

- Internal auxiliary input

5 Exit Audio Setup mode

Press [VOL] knob for at least 1 second.

1 Select the source to adjust

Press the [SRC] button.

2 Enter Audio Setup mode

Press the [VOL] knob for at least 1 second.

Subwoofer Output

3 Select the Audio Setup item to adjust

Press the [VOL] knob.

Each time you press the knob, the item to be

adjusted alternates between the items shown in

the table below.

Turning the Subwoofer output ON or OFF.

Hold down on [AM] of the Control knob for at

least 1 second.

Each time you press the button, Subwoofer

output switches ON and OFF.

4 Setup the Audio item

Turn the [VOL] knob.

When it is ON, "SW ON" is displayed.

Adjustment Item Display

Front High Pass Filter*²"HPF-F"

Range

Through/40/60/80/100/

120/150/180/220 Hz

•

You can control this function when "2Zone" of <Audio

Setup> (page 12) is set to "OFF".

Rear High Pass Filter*²"HPF-R"

Through/40/60/80/100/

120/150/180/220 Hz

Low Pass Filter*^1,2

"LPF"

50/60/80/100/120/

Through Hz

Display Setting

Changing the display mode.

Subwoofer Phase*^1,2,3"SW Phase" Normal (0°)/ Reverse (180°)

Volume offset

Loudness

Dual Zone System

"VOL Offset" –8 —

1 Enter display Control mode

Press the Control knob for at least 1 second.

"Display Control" is displayed.

"Loudness"

"2Zone"

ON/OFF

2 Select the Display mode

Press the Control knob.

Each time you press the knob, the display

alternates between the display modes shown in

the table below.

•

Volume offset: Sets each source’s volume as a

difference from the basic volume.

Loudness: Compensates for low and high tones

during low volume.

*¹You can control this item when <Subwoofer

Output> (page 12) is set to "SW ON".

*²You can control this item when "2Zone" of <Audio

Setup> (page 12) is set to "OFF".

*³You can control this item when Low Pass Filter is not

set to Through.

Display Mode Display

"Display Type A"

Dual Zone System

"Display Type B"

Main source and sub source (Auxiliary input) output

Front channel and Rear channel separately.

- Set up the channel of sub source by <Dual Zone

System Setting> (page 31).

- Select Main source by [SRC] button.

- Adjust the volume of Front channel by [VOL] knob.

- Adjust the volume of Rear channel by <Audio

Control> (page 11).

"Display Type C"

- The Audio Control has no effect on sub source.

English

1 Upper text display part

2 Middle text display part

3 Lower text display part

4 Text display part

5 Graphic display part

•

You can display the information that will be shown

in the Upper text display part, the Lower text display

part or the Level meter display part according to the

setting of Display mode. Refer to the following pages

for how to select the mode.

Display Type

Upper 1

Middle 2

Lower 3

Text 4

—

page 14

page 15

—

Graphic 5

page 18

—

3 Exit Display Control mode

Press the Control knob for at least 1 second.

English

General features

Display Type B

In Auxiliary input source

Text Selection for Display

Information

Auxiliary input name

Clock

Display

"SRC Name"

"Clock"

Selecting the text display.

1 Enter display control mode

Press the Control knob for at least 1 second.

"Display Control" is displayed.

Date

"Date"

In SIRIUS tuner source

Information

Channel Name

Song Title

Display

"Channel Name"

"Song Title"

2 Select the display Type

Press the Control knob.

Select the "Display Type B" display.

Artist Name

Composer name

Category Name

Label Name

Comment

Band & Channel Number

Clock

Date

"Artist Name"

"Composer Name"

"Category Name"

"Label Name"

"Comment"

"Channel Number"

"Clock"

"Date"

3 Select the text display part

Push the Control knob towards [FM] or [AM].

The selected text display part blinks.

4 Push the Control knob towards [4] or

[¢].

Each time you push the knob, the display

alternates between the Information displays

shown in the tables below.

In HD Radio source

In Tuner source

Information

Station name

Title

Frequency

Clock

Display

"Station Name"*

"Title"*

"Frequency"

"Clock"

"Date"

Information

Station name

Frequency

Clock

Display

"BAND+ch+SNPS"*

"BAND+ch+FREQ"

"Clock"

Date

"Date"

Date

In CD & External disc source

In Standby

Information

Disc title

Track title

Track number & Play time

Disc name

Clock

Display

"Disc Title"*

"Track Title"*

"P-Time"

"DNPS"

Information

Standby

Clock

Display

"SRC Name"

"Clock"

Date

"Date"

"Clock"

Date

"Date"

•

* If the contents of the information cannot be

displayed, Play time or Frequency is displayed.

If the contents of the information for the SIRIUS

tuner source cannot be displayed, channel number is

displayed.

When LX-AMP is connected, the item setup by the

Display mode of LX-AMP is displayed.

In Audio file source

Information

Song title & Artist name

Album name & Artist name

Folder name

File name

Play time & File number

Clock

Display

"Title/Artist"*

"Album/Artist"*

"Folder Name"

"File Name"

"P-Time"

•

Track number at Audio file displays the last 3 digits

when the track number exceeds 1000 songs.

5 Exit Display control mode

Press the Control knob for at least 1 second.

"Clock"

"Date"

Date

English

Display Type C

Text Display Switching

Changing the text display.

1 Enter display control mode

Press the Control knob for at least 1 second.

"Display Control" is displayed.

2 Select the display Type

Press the Control knob.

Select the "Display Type C" display.

3 Select the text display part

Push the Control knob towards [FM] or [AM].

The selected text display part blinks.

Select the text

Push the Control knob towards [4] or

[¢].

Refer to the table described later for setting

items.

4 Exit Display Control mode

Press the Control knob for at least 1 second.

•

Same information cannot be displayed in Upper text

display part, Middle text display part and Lower text

display part. However, the blank display is able to have

multiple selections.

If the contents of the information for the SIRIUS

tuner source cannot be displayed, channel number is

displayed.

•

When LX-AMP is connected, the item setup by the

Display mode of LX-AMP is displayed.

Track number at Audio file displays the last 3 digits

when the track number exceeds 1000 songs.

English

General features

The text display in the Upper text display

part

In SIRIUS tuner source

Information

Channel Name

Song Title

Display

"Channel Name"

"Song Title"

"Artist Name"

"Composer Name"

"Category Name"

"Label Name"

"Comment"

In Tuner source

Information

Station name

Frequency

Spectrum Analyzer & Clock

Date

Display

Artist Name

"BAND+ch+SNPS"*

"BAND+ch+FREQ"

"Speana/Clock"

"Date"

Composer name

Category Name

Label Name

Comment

Band & Channel Number

Spectrum Analyzer & Clock

Date

"Channel Number"

"Speana/Clock"

"Date"

In CD & External disc source

Information

Disc title

Track title

Track number & Play time

Disc name

Display

"Disc Title"*

"Track Title"*

"P-Time"

•

* If the contents of the information cannot be

displayed, Play time or Frequency is displayed.

"DNPS"

Spectrum Analyzer & Clock

Date

"Speana/Clock"

"Date"

In Audio file source

The text display in the Middle text display

part

Information

Display

Song title & Artist name

Album name & Artist name

Folder name

"Title/Artist"*

"Album/Artist"*

"Folder Name"

"File Name"

"P-Time"

In Tuner source

Information

Spectrum Analyzer & Clock

Date

Blank

Display

"Speana/Clock"

"Date"

File name

Play time & File number

Spectrum Analyzer & Clock

Date

"Blank"

"Speana/Clock"

"Date"

In CD & External disc source

In Standby

Information

Spectrum Analyzer & Clock

Date

Blank

Disc title

Display

"Speana/Clock"

"Date"

Information

Standby

Clock

Display

"SRC Name"

"Clock"

"Blank"

Date

"Date"

"Disc Title"*

"Track Title"*

"DNPS"

Track title

Disc name

In Auxiliary input source

Information

Display

Auxiliary input name

Spectrum Analyzer & Clock

Date

"SRC Name"

"Speana/Clock"

"Date"

In Audio file source

Information

Spectrum Analyzer & Clock

Date

Display

"Speana/Clock"

"Date"

In HD Radio source

Blank

"Blank"

Information

Station name

Title

Frequency

Spectrum Analyzer & Clock

Date

Display

"Station Name"*

"Title"*

"Frequency"

"Speana/Clock"

"Date"

Song title & Artist name

Album name & Artist name

Folder name

"Title/Artist"*

"Album/Artist"*

"Folder Name"

"File Name"

File name

English

In Standby

Information

Clock

Date

Display

"Clock"

"Date"

Blank

"Blank"

In Auxiliary input source

Information

Display

Spectrum Analyzer & Clock

Date

"Speana/Clock"

"Date"

Blank

"Blank"

In HD Radio source

Information

Spectrum Analyzer & Clock

Date

Blank

Title

Display

"Speana/Clock"

"Date"

"Blank"

"Title"*

In SIRIUS tuner source

Information

Spectrum Analyzer & Clock

Date

Display

"Speana/Clock"

"Date"

Blank

"Blank"

Channel Name

Song Title

Artist Name

Composer name

Category Name

Label

"Channel Name"

"Song Title"

"Artist Name"

"Composer Name"

"Category Name"

"Label Name"

"Comment"

Comment

•

* If the contents of the information cannot be

displayed, Kenwood Logo is displayed. However, in

HD Radio source, the display becomes blank.

English

General features

The text display in the Lower text display

part

In HD Radio source

Information

Display

In Tuner source

Indicator

Spectrum Analyzer & Clock

Date

Blank

Title

"Indicator"

"Speana/Clock"

"Date"

"Blank"

"Title"*

Information

Indicator

Spectrum Analyzer & Clock

Date

Display

"Indicator"

"Speana/Clock"

"Date"

Blank

"Blank"

In SIRIUS tuner source

In CD & External disc source

Information

Indicator

Spectrum Analyzer & Clock

Date

Blank

Channel Name

Song Title

Artist Name

Composer name

Category Name

Label

Display

"Indicator"

"Speana/Clock"

"Date"

"Blank"

"Channel Name"

"Song Title"

"Artist Name"

"Composer Name"

"Category Name"

"Label Name"

"Comment"

Information

Indicator

Spectrum Analyzer & Clock

Date

Blank

Disc title

Display

"Indicator"

"Speana/Clock"

"Date"

"Blank"

"Disc Title"*

"Track Title"*

"DNPS"

Track title

Disc name

In Audio file source

Comment

Information

Indicator

Spectrum Analyzer & Clock

Date

Display

"Indicator"

"Speana/Clock"

"Date"

•

* If the contents of the information cannot be

displayed, indicator is displayed. However, In HD

Radio source, a display becomes a blank display.

Blank

"Blank"

Song title & Artist name

Album name & Artist name

Folder name

"Title/Artist"*

"Album/Artist"*

"Folder Name"

"File Name"

Display Type A/ Display Type B

Graphic part/ Spectrum Analyzer

Display Switching

File name

In Standby

Information

Indicator

Clock

Display

"Indicator"

"Clock"

Changing the graphic Display/ Spectrum analyzer

display.

Date

Blank

"Date"

"Blank"

1 Enter display control mode

Press the Control knob for at least 1 second.

"Display Control" is displayed.

In Auxiliary input source

2 Select the display Type

Press the Control knob.

Select the "Display Type A"/ "Display Type B"

display.

Information

Indicator

Spectrum Analyzer & Clock

Date

Display

"Indicator"

"Speana/Clock"

"Date"

3 Select the graphic/ spectrum analyzer

display ("Display Type B" only)

Blank

"Blank"

Push the Control knob towards [FM] or [AM].

The blinking text display part stops.

English

4 Select the graphic/ spectrum analyzer

display part display

7 Select the characters

Push the Control knob towards [FM] or [AM].

Push the Control knob towards [4] or

[¢].

Each time you push the knob, the display

alternates between the display names shown in

the table below.

•

Enter characters by using a remote control with

numbers buttons.

Example: If you are entering "DANCE".

Character

"D"

"A"

"N"

"C"

Button

[3]

[2]

[6]

[2]

Times pressed

Graphic display/ Spectrum Analyzer display

Wallpaper 1 – 5

Spectrum analyzer 1 – 5

5 Exit Display control mode

Press the Control knob for at least 1 second.

"E"

[3]

8 Repeat steps 5 through 7 and enter the name.

9 Exit Menu mode

Press the [MENU] button.

Station/Disc Naming (SNPS/DNPS)

Attaching a title to a Station or CD.

•

When operation stops for 10 seconds the name at

that time is registered, and Name Set mode closes.

Memory numbers

1 Receive/play the station/disc you want to

attach a title to

- FM/AM: 30 stations

- Internal CD player: 10 discs

- External CD changer/ player: Varies according to the

CD changer/ player. Refer to the CD changer/ player

manual.

Change the title of station/CD by the same operation

used to name it.

•

A title cannot be attached to MD or Audio file media.

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

"Menu" is displayed.

•

3 Select Name set mode

Push the Control knob towards [FM] or [AM].

Select the "Name Set" display.

Faceplate Angle Adjustment

4 Enter Name set mode

Press the Control knob for at least 1 second.

Press the [ANG] button for at least 1 second.

5 Move the cursor to the enter character

•

Do not apply excessive force to the faceplate. It can

cause damage.

position

Push the Control knob towards [4] or

[¢].

6 Select the character type

Press the Control knob.

Each time you press the knob, the character type

alternates between the types shown in the table

below.

Character type

Alphabet upper case

Alphabet lower case

Numbers and symbols

Special characters (Accent characters)

English

General features

Theft Deterrent Faceplate

TEL Mute

The faceplate of the unit can be detached and

taken with you, helping to deter theft.

The audio system automatically mutes when a

call comes in.

Removing the Faceplate

When a call comes in

"CALL" is displayed.

The audio system pauses.

1 Turn the ignition OFF or press the [SRC]

button for at least 1 second.

The power turns OFF and the faceplate slides

open.

Listening to the audio during a call

Press the [SRC] button.

The "CALL" display disappears and the audio

system comes back ON.

2 Holding the center part of the faceplate pull

it out.

When the call ends

Hang up the phone.

The "CALL" display disappears and the audio

system comes back ON.

•

When the faceplate is kept remove open, according

to the <OFF Wait Time Setting> (page 31) setting, the

faceplate is hidden and the power turns OFF.

The faceplate is a precision piece of equipment and

can be damaged by shocks or jolts. For that reason,

keep the faceplate in its special storage case while

detached.

•

Do not expose the faceplate or its storage case to

direct sunlight or excessive heat or humidity. Also

avoid places with too much dust or the possibility of

water splashing.

Reattaching the Faceplate

1 Set the left side of the faceplate in the

faceplate bracket.

2 Press the right side of the faceplate until it

locks.

•

Use the enclosed or dedicated faceplate. Using a

faceplate other than the specified one may cause your

unit to malfunction.

English

Tuner features

AUTO/AME

1 — 6

SRC

Control knob

Band display

Frequency display

FM1-6ch 98.1

SNPS

Preset station number

ST indicator

Tuning

Tuning Mode

Selecting the station.

Choose the tuning mode.

Press the [AUTO] button.

1 Select tuner source

Press the [SRC] button.

Select the "TUNER" display.

Each time you press the button, the Tuning

mode alternates between the modes shown in

the table below.

2 Select the band

Tuning mode

Auto seek

Display

Operation

Push the Control knob towards [FM] or [AM].

Each time you push the knob toward [FM], it

switches between the FM1, FM2, and FM3 bands.

"Seek Mode: Automatic search for a station.

Auto1"

Preset station seek "Seek Mode: Search in order of the stations

Auto2" in the Preset memory.

3 Tune up or down band

Push the Control knob towards [4] or

[¢].

Manual

"Seek Mode: Normal manual tuning control.

Manual"

•

During reception of stereo stations the "ST" indicator

is ON.

English

Tuner features

Function of remote control

Auto Memory Entry

Direct Access Tuning

Putting stations with good reception in the

memory automatically.

Entering the frequency and tuning.

1 Select the band for Auto Memory Entry

Push the Control knob towards [FM] or [AM].

1 Select the band

Press the [FM] or [AM] button.

2 Open Auto Memory Entry

2 Enter Direct Access Tuning mode

Press the [DIRECT] button on the remote

control.

Press the [AME] button for at least 2 seconds.

When 6 stations that can be received are put in

the memory Auto Memory Entry closes.

"– – – –" is displayed.

3 Enter the frequency

Press the number buttons on the remote

control.

Example:

Preset Tuning

Recalling the stations in the memory.

Desired frequency

92.1 MHz (FM)

810 kHz (AM)

Press button

[0], [9], [2], [1]

[0], [8], [1], [0]

1 Select the band

Push the Control knob towards [FM] or [AM].

Cancelling Direct Access Tuning

Press the [DIRECT] button on the remote

control.

2 Recall the station

Press the desired [1] — [6] button.

Station Preset Memory

Putting a station in the memory.

1 Select the band

Push the Control knob towards [FM] or [AM].

2 Select the frequency to put in the memory

Push the Control knob towards [4] or

[¢].

3 Put the frequency in the memory

Press the desired [1] — [6] button for at least

2 seconds.

The preset number display blinks 1 time.

On each band, 1 station can be put in the

memory on each [1] — [6] button.

English

CD/Audio file/External disc control features

S.MODE

RDM/3/

D.RDM

F.SEL

SRC

Control knob

SCAN

REP

M.RDM

Track number

Track time

MP3 T-01 0:12

Title/Artist

IN indicator

When a disc is inserted

Press the [SRC] button.

Playing CD & Audio file

Select the "Compact Disc" display.

When there is no disc inserted

Pause and play

1 Open the panel

Press the Control knob.

Each time you press the knob, the audio pauses

or plays.

Press the [0] button.

2 Insert a disc.

Eject the disc

•

When the faceplate slides open, it might interfere

with the shift lever or other vehicle function. If this

happens, pay attention to safety and move the shift

lever or take an appropriate action to remove the

obstacle, then operate the unit.

Insert the disc horizontal to the slot. If you insert the

Disc as you push down on the Disc, it may scratch the

Disc.

1 Eject the disc

Press the [0] button.

2 Return the panel to the original position

Press the [0] button.

•

The sound will be temporarily muted while the

faceplate is moving.

You can cancel the announcement when selecting

the folder by <Voice Index> (page 34) during the play

of the ACDrive.

•

When a disc is inserted the "IN" indicator is ON.

English

CD/Audio file/External disc control features

Function of disc changer/ Audio file

Playing External Disc

Disc Search/Folder Search

Playing discs set in the optional accessory disc

player connected to this unit.

Selecting the disc set in the Disc changer or the

folder recorded on the Audio file media.

Press the [SRC] button.

Select the display for the disc player you want.

Display examples:

Push the Control knob towards [FM] or [AM].

Display

"CD Changer"

"MD Changer"

Disc player

CD changer

MD changer

Function of remote control

Direct Track/File Search

Pause and play

Doing Track/File Search by entering the track/file

number.

Press the Control knob.

Each time you press the knob, the audio pauses

or plays.

1 Enter the track/file number

Press the number buttons on the remote

control.

•

The functions that can be used and the information

that can be displayed will differ depending on the

external disc players being connected.

•

You can select Direct File Search up to 999.

2 Do Track/File Search

Press the [4] or [¢] button.

Cancelling Direct Track/File Search

Press the [38] button.

Fast Forwarding and Reversing

Fast Forwarding

Hold down toward [¢] with the Control

knob.

Release your finger to play the disc at that point.

Function of disc changers with remote control

Direct Disc Search

Reversing

Doing Disc Search by entering the disc number.

Hold down toward [4] with the Control

knob.

Release your finger to play the disc at that point.

1 Enter the disc number

Press the number buttons on the remote

control.

•

There is no sound while the Audio file is being

searched.

2 Do Disc Search

Press the [+] or [–] button.

Cancelling Direct Disc Search

Press the [38] button.

Track/File Search

Searching for a song on the disc or in the Audio

file folder.

•

Input "0" to select disc 10.

Push the Control knob towards [4] or

[¢].

English

Function of disc changer

Track/File/Disc/Folder Repeat

Magazine Random Play

Replaying the song, disc in the Disc changer or

Audio file folder you are listening to.

Play the songs on all the discs in the disc changer

in random order.

Press the [REP] button.

Each time you press the button, the Repeat Play

alternates between the modes shown in the

tables below.

Press the [M.RDM] button.

Each time you press the button, the Magazine

Random Play turns ON or OFF.

When the Magazine Random mode is ON,

"Magazine RDM ON" is displayed.

In CD & External disc source

Repeat play

Track Repeat

Display

"Repeat ON"/ "Track Repeat ON"

"Disc Repeat ON"

"Repeat OFF"

•

When you push the Control knob toward [¢], the

Disc Repeat (In Disc Changer)

OFF

next random song starts.

In Audio file

Function of Audio file

Repeat play

File Repeat

Folder Repeat

OFF

Display

"File Repeat ON"

"Folder Repeat ON"

"Repeat OFF"

Disc Random Play

Playing randomly from all of the Audio files

recorded in the disc.

Press the [RDM] button for at least 1 second.

When the random mode is ON, "Disc Random

ON" is displayed.

Scan Play

Cancelling the Disc Random Play

Press the [RDM] button.

Playing the first part of each song on the disc

or Audio file folder you are listening to and

searching for the song you want to hear.

•

When you push the Control knob toward [¢], the

next random song starts.

1 Start Scan Play

Press the [SCAN] button.

"Scan ON" is displayed.

2 Release the button when the song you want

to hear is played

Press the [SCAN] button.

Random Play

Play all the songs on the disc or Audio file folder

in random order.

Press the [RDM] button.

Each time you press the button, Random Play

turns ON or OFF.

When the Random mode is ON, "Random ON" is

displayed.

•

When you push the Control knob toward [¢], the

next random song starts.

English

CD/Audio file/External disc control features

Function of Audio file

Function of ACDrive disc

Folder Select

Switching the Play mode

Quickly selecting the folder you want to hear.

Arrange the playing orders of the songs by

categories.

1 Enter Folder Select mode

Press the [F.SEL] button.

"Select Mode" is displayed.

During Select mode the folder information is

displayed as shown below.

Folder number display

Press the [S.MODE] button.

Each time you press the button, the Play mode

alternates between the modes shown on the

table below.

Play mode

Category which is to be arranged

"PlayList Mode" Play list order.

"Genre Mode" By genre.

Displays the number in the folder belonging to

the currently selected folder.

5 5 5 5 5 5 5

"Artist Mode"

By artist.

"Album Mode" By album.

"Folder Mode" By the folder recorded in Disc.

Select F02

Folder Name

5 5 5 5 5 5 5

•

The category information of each song is the data

registered in Media Manager when ACDrive disc is

being generated.

Folder name display

Displays the current folder name.

•

You can cancel the announcement made when the

mode is changed by <Voice Index> (page 34).

You can select the advancement of the Play mode

information by [AM] and [FM] keys.

•

The Folder number display does not function when

<Disc Random Play> (page 25) is ON.

2 Select the folder level*

Push the Control knob towards [FM] or [AM].

With the [FM] of the Control knob, you move

1 level down and with the [AM] of the Control

knob, 1 level up.

Function of ACDrive disc

Letter Seek

Selecting a folder in the same level

Push the Control knob towards [4] or

[¢].

With the [4] of the Control knob, you move

to the previous folder, and with the [¢] of the

Control knob, to the next folder.

You can search for the song, you want to play, by

selecting the initial of Genre name, Artist name,

or Album name.

1 Enter the Letter Seek mode

Press the [S.MODE] button for at least 1

second.

Returning to the top level*

Press the [3] button.

•

This operation does not function when <Disc Random

Play> (page 25) is ON.

This function is available only when the Play mode is

set Genre, Artist, or Album.

•

* You can operate this function when <Switching the

Play mode> (page 26) is set to "Folder Mode" while

playing ACDrive disc.

Cancelling the Letter Seek

Press the [S.MODE] button.

3 Decide the folder to play

Press the Control knob.

The Folder Select mode releases, and the Audio

file in the folder being displayed plays.

Cancelling the Folder Select mode

Press the [F.SEL] button.

English

2 Start the Letter Seek

Push the Control knob towards [4] or

[¢].

The initial of Genre name, Artist name, or Album

name is displayed and announced in order.

•

The announcement of the initial can be canceled by

<Voice Index> (page34).

When you push the Control knob to the reverse [4]

or [¢] during Letter Seek, the initial is displayed

and announced in the reversed order.

•

Once Letter Seek starts, it cannot be cancelled.

3 Select the song to play

Press the Control knob when the initial of

the song you are searching is displayed and

announced.

The selected initial group plays.

Text/Title Scroll

Scrolling the displayed CD text, Audio file text, or

MD title.

Push the Control knob toward [FM] for at

least 1 second.

English

HD Radio control features

AUTO/AME

1 — 6

SRC

Control knob

Band display

Frequency display

HF1-6ch 98.1

Station Name

Title

Preset station number

Tuning

Selecting the station.

•

When you connect an HD Radio, Tuner features of

the unit are disabled and changed to HD Radio tuner

features. A portion of the setting methods including

the Tuning Mode will change.

With the HD Radio tuner, you can use the similar

functions to <Station Preset Memory>, <Auto

Memory Entry>, and <Preset Tuning> of Tuner

features. Refer to Tuner features for how to use the

functions.

1 Select HD Radio source

Press the [SRC] button.

Select the "HD Radio" display.

2 Select the HD FM band

Push the Control knob toward [FM].

Each time you push the knob to [FM], the band

alternates between the HF1, HF2, and HF3 bands.

Select the HD AM band

Push the Control knob toward [AM].

3 Tune up or down band

Push the Control knob towards [4] or

[¢].

English

Menu system

SRC

Control knob

Clock Adjust

Beep:ON

Security

You can continue by returning to step 2 and

setting other items.

Menu System

Setting beep sound during operation, etc.

functions.

The Menu system basic operation method is

explained here. The reference for the Menu items

and their setting content is after this operation

explanation.

4 Exit Menu mode

Press the [MENU] button.

•

When other items those applicable to the basic

operation method above are displayed, their setting

content chart is entered. (Normally the setting listed at

the top of the chart is the original setting.)

Also, the explanation for items that are not applicable

(<Manual Clock Adjustment> etc.) are entered step

by step.

1 Enter Menu mode

Press the [MENU] button for at least 1 second.

"Menu" is displayed.

2 Select the menu item

•

Three menu items appear on the display. The menu

item displayed at the center is the one you can adjust.

Push the Control knob towards [FM] or [AM].

Example: When you want to set the beep sound

select the "Beep" display.

3 Set the menu item

Push the Control knob towards [4] or

[¢].

Example: When you select "Beep", each time you

push the knob it alternates between

"Beep:ON" or "Beep:OFF". Select 1 of

them as the setting.

English

Menu system

In Standby mode

Press the Reset button when the audio unit is

removed from the battery power source

Security Code

1 Turn the power ON.

2 Do the step 4 through 7 operation, and enter

the Security Code.

Because authorization by the Security Code is

required when the audio unit is removed from

the vehicle, personalizing this unit by using the

Security Code is helpful in preventing theft.

"Approved" is displayed.

You can being using the unit.

•

Setup Security Code when the <Demonstration mode

Setting> (page 35) is set as OFF.

When you activate the Security Code function, the code

cannot be changed and the function cannot be released.

Note, you can set the Security Code with a 4 digit

number of your choice.

In Standby mode

Touch Sensor Tone

Setting the operation check sound (beep sound)

ON/OFF.

1 Enter Standby

Press the [SRC] button.

Select the "STANDBY" display.

Display

"Beep:ON"

"Beep:OFF"

Setting

Beep is heard.

Beep canceled.

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

When "Menu" is displayed, "Security" is also

displayed.

In Standby mode

3 Enter Security Code mode

Press the Control knob for at least 1 second.

When "Enter" is displayed, "CODE" is also

displayed.

Manual Clock Adjustment

1 Select Clock Adjustment mode

Push the Control knob towards [FM] or [AM].

Select the "Clock Adjust" display.

4 Select the digits to enter

Push the Control knob towards [4] or

[¢].

2 Enter Clock Adjust mode

Press the Control knob for at least 1 second.

The clock display blinks.

5 Select the Security Code numbers

Push the Control knob towards [FM] or [AM].

3 Adjust the hours

Push the Control knob towards [FM] or [AM].

6 Repeat steps 4 and 5, and complete the

Security Code.

Adjust the minutes

7 Confirm the Security Code

Press the Control knob for at least 3 seconds.

When "Re-Enter" is displayed, "CODE" is also

displayed.

Push the Control knob towards [4] or

[¢].

4 Exit Clock adjustment mode

Press the [MENU] button.

8 Do the step 4 through 7 operation, and

reenter the Security Code.

"Approved" is displayed.

The Security Code function activates.

•

If you enter the wrong Code in steps 4 through 6,

repeat from step 4.

English

In Standby mode

Date Adjustment

OFF Wait Time Setting

Setting the time until the faceplate hiding

operation starts after the power is turned OFF.

You can only remove the faceplate during the set

time period.

1 Select Date Adjust mode

Push the knob towards [FM] or [AM].

Select the "Date Adjust" display.

2 Enter Date Adjust mode

Press the Control knob for at least 1 second.

The date display blinks.

Display and Setting

"Off Wait:0sec"

3 Selecting the item (day, month, or year) to

"Off Wait:3sec" (Original setting)

"Off Wait:25sec"

adjust

Push the Control knob towards [4] or

[¢].

The items that are blinking are items that you

can adjust.

In Standby mode

4 Adjust each item

Push the Control knob towards [FM] or [AM].

Built-in Amp Setting

5 Repeat step 3 and 4 operation and adjust the

Controlling the built-in amplifier.

Turning OFF this control enhances the preout

quality.

date.

6 Exit Date adjustment mode

Press the [MENU] button.

Display

Setting

"AMP:ON"

"AMP:OFF"

The built-in amplifier activates.

The built-in amplifier deactivates.

In Standby mode

Date Mode

Setting the date format.

Other than Standby mode/

When the Dual Zone System is ON

1 Select Date Mode

Dual Zone System Setting

Push the Control knob towards [FM] or [AM].

Select the "Date Mode" display.

Setting the Front channel and Rear channel

sound in the Dual Zone System.

2 Select the date format

Push the Control knob towards [4] or

[¢].

Display

Setting

"Zone2:Rear"

Sub source (Auxiliary input source) is to be rear

channel.

3 Exit Date mode

Push the Control knob towards [FM] or [AM].

"Zone2:Front"

Sub source (Auxiliary input source) is to be front

channel.

In Standby mode

Dimmer

Dimming this unit’s display automatically when

the vehicle light switch is turned ON.

Display

Setting

"Dimmer:ON"

"Dimmer:OFF"

The display dims.

The display doesn’t dim.

English

Menu system

Other than Standby mode

4 Adjust the AMP Control item

Push the Control knob towards [4] or

[¢].

B.M.S. (Bass Management System)

Adjust the bass boost level of the external

amplifier using the main unit.

5 Exit AMP Control mode

Press the [MENU] button.

Display

Setting

"AMP Bass:Flat"

"AMP Bass:+6"

"AMP Bass:+12"

"AMP Bass:+18"

Bass boost level is flat.

•

You cannot use the LX AMP operation during standby

mode.

Bass boost level is low (+6dB).

Bass boost level is mid (+12dB).

Bass boost level is high (+18dB).

In FM reception

•

Refer to the catalog or instruction manual for power

CRSC (Clean Reception System

Circuit)

amplifiers that can be controlled from this unit.

For amplifiers, there are the models you can set from

Flat to +18 dB, and the models you can set from Flat

to +12 dB.

When an amplifier that can only be set to +12 is

connected to the unit, "AMP Bass:+18" will not work

correctly even if it is selected.

Temporarily have reception alternate from

stereo to mono to reduce multi-path noise when

listening to the FM station.

Display

Setting

"CRSC:ON"

"CRSC:OFF"

The CRSC is ON.

The CRSC is OFF.

Other than Standby mode

B.M.S. Frequency Offset

•

Strong electrical fields (such as from power lines) may

Setting the central frequency, boosted by B.M.S.

cause unstable sound quality when CRSC is turned

ON. In such a situation, turn it OFF.

Display

Setting

"AMP FREQ:Normal"

"AMP FREQ:Low"

Boost with the normal central frequency.

Drop the normal central frequency 20%.

In HD Radio mode

Receive mode Setting

Sets the receive mode.

When LX AMP unit connecting

AMP Control

1 Select the Receive mode

Push the Control knob towards [FM] or [AM].

Select the "Receive Mode" display.

You can control the LX AMP connected to the

unit.

2 Enter Receive mode

1 Select AMP Control mode

Push the Control knob towards [FM] or [AM].

Select the "AMS Control" display.

Press the Control knob for at least 1 second.

3 Set the Receive mode

Push the Control knob towards [FM] or [AM].

Each time you push the knob, the Receive mode

alternates between the modes shown in the

table below.

2 Enter AMP Control mode

Press the Control knob for at least 1 second.

3 Select the AMP Control item for adjustment

Push the Control knob towards [FM] or [AM].

•

For the details on the AMP Control item, see the

Instruction manual attached to the LX AMP.

English

3 Select Auxiliary input display setting mode

Push the Control knob towards [FM] or [AM].

Select the "Name Set" display.

Receive mode Display

Operation

Auto mode

"Auto"

Analog broadcasts and digital

broadcasts will be switched

automatically.

When both are being transmitted,

the digital broadcast will have

priority.

4 Enter Auxiliary input display setting mode

Press the Control knob for at least 1 second.

The presently selected Auxiliary input display is

displayed.

Digital

Analog

"Digital"

"Analog"

Digital broadcasts only.

Analog broadcasts only.

5 Select the Auxiliary input display

Push the Control knob towards [4] or

4 Exit Receive mode

Press the [MENU] button.

[¢].

Each time you press the button, the display

alternates as listed below.

• "AUX"/ "AUX EXT"

• "DVD"

• "PORTABLE"

• "GAME"

•

Even if the Receive mode is set to "Auto", when the

Ball game mode program (non-delayed broadcast

program) is received, the Receive mode will

automatically switch to Analog broadcast only.

• "VIDEO"

• "TV"

6 Exit Auxiliary input display setting mode

Press the [MENU] button.

In SIRIUS tuner source

SIRIUS ID (ESN) display

Displaying the SIRIUS ID (Electronic Serial

Number)

•

When operation stops for 10 seconds, the name at

that time is registered, and the Auxiliary input display

setting mode closes.

The Auxiliary Input Display can be set only when the

built-in auxiliary input or the auxiliary input of optional

KCA-S210A is used.

Display

"ESN:************"

•

Serial & SIRIUS ID (ESN)

It is important to retain the unit serial number and

the electronic SIRIUS Identification number for service

activation and potential service changes.

Text Scroll

Setting the displayed text scroll.

Display

"Scroll:Auto"

"Scroll:Manual"

Setting

Repeats scroll.

Scrolls when the display changes.

Auxiliary Input Display Setting &

Station/Disc Naming

Selecting the display when changing to Auxiliary

input source. For the Station/Disc Naming refer to

the <Station/Disc Naming (SNPS/DNPS)> (page

19).

•

The text scrolled is listed below.

- CD text

- Folder name/ File name/ Song title/ Artist name/

Album name

- MD title

1 Select Auxiliary input source

Press the [SRC] button.

Select the "AUX"/ "AUX EXT" display.

- Text for the SIRIUS tuner source, HD Radio source,

including Channel name, etc.

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

"Menu" is displayed.

English

Menu system

In Standby mode

In CD mode

Built-in Auxiliary input Setting

Unique ID display

Set the Built-in Auxiliary Input function.

Displaying the serial number for each product.

Display

Setting

1 Select the unique ID display mode

Push the Control knob towards [FM] or [AM].

Select the "ACD Unique ID" display.

"Builtin AUX:OFF" When selecting the source there’s no Auxiliary

Input.

"Builtin AUX:ON" When selecting the source there’s Auxiliary Input.

2 Display the unique ID

Push the Control knob towards [4] or

[¢].

In Standby mode

CD Read Setting

Audio Preset Memory

When there is a problem with playing a CD with

special format, this setting plays the CD by force.

Registering the value setup by Sound Control. The

memory cannot be erased by the Reset button.

Display

Setting

"CD Read:1"

"CD Read:2"

Play CD and Audio file.

Play CD by force.

1 Setup Sound Control

Refer to the following operations to setup the

Sound Control.

- <Audio Control> (page 11)

•

Setting "CD Read:2" cannot play Audio file.

- <Audio Setup> (page 12)

Some music CDs may not play even in the "CD

Read:2" mode.

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

"Menu" is displayed.

3 Select Audio Preset mode

Push the Control knob towards [FM] or [AM].

Select the "Audio Preset" display.

Function of ACDrive disc

Voice Index

Setting the announcement during the play of

ACDrive disc.

4 Enter Audio Preset mode

Press the Control knob for at least 1 second.

Display

"Voice Index:ON"

"Voice Index:OFF"

Setting

Guide is announced.

Not be announced.

5 Select the Audio Preset Memory

Push the Control knob towards [FM] or [AM].

Select the "Memory" display.

6 Put the Audio Preset in the memory

Press the Control knob for at least 2 seconds.

The "Memory" display blinks 1 time.

In CD mode

7 Exit Menu mode

Press the [MENU] button.

ACDrive firmware version display

Displaying the firmware version with the ACDrive

function.

•

When you press the Reset, all the sources will be the

setting value which is registered.

The following items cannot be registered.

Volume, Balance, Fader, Loudness, Volume offset, Dual

Zone System, Rear Volume

1 Select the firmware version display mode

Push the Control knob towards [FM] or [AM].

Select the "ACD F/W Version" display.

2 Display the ACDrive firmware version

Push the Control knob towards [4] or

[¢].

English

Audio Preset Call

Recalling the sound setup registered by <Audio

Preset Memory> (page 34).

1 Select the source

Press the [SRC] button.

2 Enter Menu mode

Press the [MENU] button for at least 1 second.

"Menu" is displayed.

3 Select Audio Preset mode

Push the Control knob towards [FM] or [AM].

Select the "Audio Preset" display.

4 Enter Audio Preset mode

Press the Control knob for at least 1 second.

5 Select the Audio Preset Recall

Push the Control knob towards [FM] or [AM].

Select the "Recall" display.

6 Recall the Audio Preset

Press the Control knob for at least 2 seconds.

The "Recall" display blinks 1 time.

7 Exit Menu mode

Press the [MENU] button.

•

The User memory of <System Q> (page 10) is

changed to the value which was recalled.

The source tone memory item of <Audio Control>

(page 11) is changed to the value which was recalled

by the selected source.

In Standby mode

Demonstration mode Setting

Sets the demonstration mode.

1 Select the Demonstration mode

Push the Control knob towards [FM] or [AM].

Select the "DEMO Mode" display.

2 Set the Demonstration mode

Press the Control knob for at least 2 seconds.

Each time you press the knob at least 2 seconds,

the Demonstration mode alternates between the

settings shown in the table below.

Display

Setting

"DEMO Mode:ON"

"DEMO Mode:OFF"

The Demonstration mode function is ON.

Exit Demonstration mode (Normal mode).

English

Basic Operations of remote control

43$

"55

70-

32#

!4 4

6/,

ꢀꢁ

!5$

"6%

ꢀꢁ

&-ꢄ

ꢂ

ꢂꢀD

!-n

ꢁꢂ:/.%

!"#

^'.ꢀ".ꢀꢁꢀo

$)2%#4

ꢀ/+

%*3&$5

$%&

-./

789

'()

*+,

023

456

2ꢃ6/,

Loading and Replacing the battery

Basic operations

Use two "AA"-size batteries.

Slide the cover while pressing downwards to

remove it as illustrated.

Insert the batteries with the + and – poles aligned

properly, following the illustration inside the case.

[VOL] buttons

Adjusts the volume.

[SRC] button

Each time you press the button, the source

alternates.

For the source alternating order refer to

<Selecting the Source> (page 10).

[ATT] button

Turns the volume down quickly.

When the button is pressed again, the volume

returns to the previous level.

[

] button

Adjusts the Faceplate Angle.

2WARNING

•

Store unused batteries out of the reach of children.

Contact a doctor immediately if the battery is

accidentally swallowed.

•

Do not set the remote control in hot places such as

above the dashboard.

English

Audio Control

In Disc source

[AUD] button

Selects the Audio item to be adjusted.

[4]/ [¢] buttons

Going forwards and backwards between track/

files.

[VOL] buttons

Adjusts the Audio item.

[+]/ [–] buttons

Going forwards and backwards between disc/

folders.

•

Refer to <Audio Control> (page 11) for the operation

method, such as the procedures for Audio control and

others operations.

The remote control can only select and adjust the

Basic Audio item. Selecting and adjusting of the Detail

Audio item cannot be done.

[38] button

Each time you press the button, the song pauses

or plays.

[0] — [9] buttons

When in <Direct Track/File Search> (page 24) and

<Direct Disc Search> (page 24), enters the track/

file/disc number.

Dual Zone System

[2-ZONE] button

Each time you press the button, "2Zone" of

<Audio Setup> (page 12) is turned ON or OFF.

In SIRIUS tuner source

[FM] button

Selects the preset band.

[5]/ [∞] buttons

Adjusts the volume of the rear channel.

The rear channel activates while the Dual Zone

System is ON.

[4]/ [¢] buttons

Searches up or down channels.

[0] — [9] buttons

Press buttons [1] — [6] to recall preset channels.

In Tuner source

[DIRECT] button

Enters and cancels the <Direct Access Tuning>

mode.

[FM]/ [AM] buttons

Selects the band.

Each time you press the [FM] button, the band

alternates between the FM1, FM2, and FM3

bands.

•

Refer to the instruction manual of SIRIUS Satellite radio

tuner for <Direct Access Tuning> function.

[4]/ [¢] buttons

Tune up or down band.

[0] — [9] buttons

Press buttons [1] — [6] to recall preset stations.

[DIRECT] button

Enters and cancels the <Direct Access Tuning>

(page 22) mode.

English

Basic Operations of remote control

In HD Radio source

[FM] button

Selects the HD FM band.

Each time you press the [FM] button, the band

alternates between the HF1, HF2, and HF3 bands.

[AM] button

Selects the HD AM band.

[4]/ [¢] buttons

Tunes up or down bands.

[0] — [9] buttons

Press buttons [1] — [6] to recall preset stations.

English

Accessories/ Installation Procedure

Accessories

Installation Procedure

1. To prevent a short circuit, remove the key from

the ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the speaker wires of the wiring harness.

..........1

4. Connect the wiring harness wires in the

following order: ground, battery, ignition.

5. Connect the wiring harness connector to the

unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

..........2

2WARNING

..........2

If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

..........2

•

If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that can be

turned on and off with the ignition key. If you connect

the ignition wire to a power source with a constant

voltage supply, as with battery wires, the battery may die.

If the console has a lid, make sure to install the unit so

that the faceplate will not hit the lid when closing and

opening.

..........1

•

If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with

one with the same rating.

Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not remove

the caps on the ends of the unconnected wires or the

terminals.

..........2

•

Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail

to work if you share the - wires or ground them to any

metal part in the car.

..........1

•

When only two speakers are being connected to the

system, connect the connectors either to both the front

output terminals or to both the rear output terminals

(do not mix front and rear). For example, if you connect

the + connector of the left speaker to a front output

terminal, do not connect the - connector to a rear

output terminal.

..........1

•

After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

Mount the unit so that the mounting angle is 30° or less.

English

Connecting Wires to Terminals

AUX left input (White)

AUX right input (Red)

Sub Woofer left output (White)

Sub Woofer right output (Red)

Front left output (White)

Front right output (Red)

Rear left output (White)

Rear right output (Red)

To Kenwood disc changer/

External optional accessory

To connect these leads, refer to the

relevant instruction manuals.

FM/AM antenna input

Fuse (10A)

If no connections are made, do not let the wire come out from the tab.

Wiring harness

(Accessory1)

When using the optional power amplifier, connect to its

power control terminal.

*°ꢁ" /

Power control wire (Blue/White)

Depending on what antenna you are using, connect either

to the control terminal of the motor antenna, or to the

power terminal for the booster amplifier of the film-type

antenna.

ꢀ /°

Motor antenna control wire (Blue)

TEL mute wire (Brown)

ÊÊÊꢁ" /

Connect to the terminal that is grounded when

either the telephone rings or during conversation.

To connect the Kenwood navigation system, consult

your navigation manual.

ꢂ1/ꢃ

To "EXT.AMP.CONT." terminal of the amplifier having

the external amp control function.

External amplifier control wire

(Pink/Black)

To car light control switch

Dimmer control wire (Orange / White)

White/Black

To front left speaker

To front right speaker

To rear left speaker

To rear right speaker

Ignition key switch

White

Gray/Black

Gray

Green/Black

Green

Purple/Black

Purple

Car fuse box

ACC

Ignition wire (Red)

Car fuse box

(Main fuse)

Battery wire (Yellow)

Ground wire (Black) ·(To car chassis)

Battery

English

Installation

non-Japanese cars

Japanese cars

Accessory6

(follow indications for L/R)

Metal mounting strap

(commercially available)

Factory-installed

Radio Bracket

Firewall or metal support

Factory-installed

Radio Bracket

Bend the tabs of the

mounting sleeve with a

screwdriver or similar utensil

and attach it in place.

Accessory7

(place thick part on bottom)

Factory trim bezel

Self-tapping screw

(commercially available)

8mm

Screw (M4X8)

(commercially available)

5mm

Accessory3...for Nissan car

Accessory4...for Toyota car

•

Make sure that the unit is installed securely in place. If

the unit is unstable, it may malfunction (for example, the

sound may skip).

•

Damage to the unit will result from using screws other

than those provided.

A pair of J-Car Brackets (Accessory 6) are not used when

fitting in a Toyota car.

•

To attach this unit, make sure the front of the control

panel faces you and fit it into the mounting sleeve by

pressing the four corners of the hard rubber frame at the

same time.

Do not apply strong pressure to other sections than the

corners; otherwise troubles such as the impossibility of

opening or closing the panel may result.

English

Installation

Screwing the Faceplate on the Unit

If you want to fasten the faceplate to the main

unit so that it does not fall off, screw in the

provided screws in the holes shown below.

1 Refer to the function <Theft Deterrent

Faceplate> (page 20) and remove the faceplate.

2 Insert the provided screw into the hole at the

center of the bottom side of the faceplate which

you have removed from the unit.

Accessory5

3 Refer to the section <Theft Deterrent Faceplate>

(page 20) and then reattaching the faceplate.

•

Never insert the screw in any other screw hole than the

one specified. If you screw them in another hole, it will

contact and may cause damage to the mechanical parts

inside the unit.

English

Removing the Unit

Removing the hard rubber frame

Removing the Unit

Insert the removal tool into the indentations in

the hard rubber frame, and pull it gently until the

lock is released.

1 Refer to the section <Removing the hard rubber

frame> (page 43) and then remove the hard

rubber frame.

2 Remove the screw (M4 × 8) on the back panel.

3 Insert the two removal tools deeply into the slots

on each side, as shown.

Accessory8

Removal tool

Screw (M4X8)

(commercially available)

Accessory2

Removal tool

4 Push upward the removal tool toward the top,

and pull out the unit halfway while pressing

towards the inside.

•

Be careful to avoid injury from the catch pins on the

removal tool.

5 Pull the unit all the way out with your hands,

being careful not to drop it.

English

Troubleshooting Guide

What might seem to be a malfunction in your unit

may just be the result of slight misoperation or

miswiring. Before calling service, first check the

following table for possible problems.

? No sound can be heard, or the volume is low.

✔

The fader or balance settings are set all the way to

one side.

☞

Center the fader and balance settings.

✔

The input/output wires or wiring harness are

connected incorrectly.

☞

Reconnect the input/output wires or the

wiring harness correctly. See the section on

<Connecting Wires to Terminals>.

General

? The power does not turn ON.

✔

The fuse has blown.

✔

The values of Volume offset are low.

☞

After checking for short circuits in the wires,

replace the fuse with one with the same

rating.

Turn up the Volume offset, referring to the

section on <Audio Control> (page 11).

The <Built-in Amp Setting> (page 31) is OFF.

Turn it ON.

☞

? There’s a source you can’t switch.

✔

There’s no media inserted.

? The sound quality is poor or distorted.

☞

Set the media you want to listen to. If there’s

no media in this unit, you can’t switch to each

source.

✔

One of the speaker wires is being pinched by a

screw in the car.

☞

Check the speaker wiring.

✔

The Disc changer isn’t connected.

✔

The speakers are not wired correctly.

☞

Connect the Disc changer. If the Disc changer

isn’t connected to it’s input terminal, You can’t

switch to an external disc source.

Reconnect the speaker wires so that each

output terminal is connected to a different

speaker.

? The memory is erased when the ignition is

turned OFF.

? The Touch Sensor Tone doesn’t sound.

The preout jack is being used.

✔

The ignition and battery wire are incorrectly

☞

The Touch Sensor Tone can’t be output from

the preout jack.

connected.

☞

Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

? The Dimmer function doesn’t work.

✔

The Dimmer wire isn’t connected correctly.

Check the Dimmer wire connection.

The <Dimmer> (page 31) is OFF.

Turn it ON.

? There’s no loudness effect.

You’re using Subwoofer preout.

Loudness has no effect in Subwoofer preout.

☞

✔

☞

? The TEL mute function does not work.

The TEL mute wire is not connected properly.

? The panel is not hidden even when the power is

turned off.

✔

☞

Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

✔

The protection function for preventing fingers or

other things from getting caught in between the

panel and this unit has been activated.

? The TEL mute function turns ON even though the

TEL mute wire is not connected.

☞

Turn off the power again.

✔

The TEL mute wire is touching a metal part of the

car.

☞

Pull the TEL mute wire away from the metal

part of the car.

? Even if Loudness is turned ON, high-pitched tone

isn’t compensated for.

✔

Tuner source is selected.

☞

High-pitched tone isn’t compensated for when

in Tuner source.

English

Tuner source

? Direct Search can’t be done.

Another function is ON.

Turn Random Play or other functions OFF.

✔

? Radio reception is poor.

☞

✔

The car antenna is not extended.

☞

Pull the antenna out all the way.

? Track Search can’t be done.

For the discs first or last song.

✔

The antenna control wire is not connected.

☞

✔

Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

☞

For each disc, Track Search cannot be done in

the backward direction for the first song or in

the forward direction for the last song.

? The desired frequency can’t be entered with the

Direct Access Tuning.

Audio file source

✔

A station that can’t be received is being entered.

☞

Enter a station that can be received.

? Cannot play an Audio file.

✔

You’re trying to enter a frequency with a 0.01 MHz

unit.

☞

✔

The media is scratched or dirty.

☞

Clean the media, referring to the CD cleaning

of the section on <About CDs> (page 7).

What can be designated in the FM band is to

0.1 MHz.

? The sound skips when an Audio file is being

played.

Disc source

✔

The media is scratched or dirty.

? "AUX EXT" is displayed without achieving

☞

Clean the media, referring to the CD cleaning

of the section on <About CDs> (page 7).

External disc control mode.

✔

Unsupported disc changer is connected.

✔

The recording condition is bad.

Record the media again or use another media.

☞

Use the disc changer mentioned in the

<About CD players/disc changers connected

to this unit> (page 4) of the section on <Safety

precautions>.

☞

? The Audio file track time isn’t displayed correctly.

✔

---

☞

There are times when it isn’t displayed

correctly according to the Audio file recording

conditions.

? The specified disc does not play, but another one

plays instead.

✔

The specified CD is quite dirty.

☞

Clean the CD.

HD Radio source

✔

The disc is loaded in a different slot from that

specified.

☞

? No sound can be heard, or the volume is low.

Eject the disc magazine and check the

number for the specified disc.

✔

The preset broadcast station is not transmitting

in the mode that was set with <Receive mode

Setting> (page 32).

✔

The disc is severely scratched.

Try another disc instead.

☞

Please set <Receive mode Setting> to "Auto".

✔

In digital AM broadcasting, receive mode switches

between stereo and monaural too often.

? A CD ejects as soon as it is loaded.

The CD is quite dirty.

✔

☞

Receiving condition is bad or unstable.

Stereo is chosen when receiving condition is

good, and it switches to monaural when the

condition becomes bad.

☞

Clean the CD, referring to the CD cleaning of

the section on <About CDs> (page 7).

? Can’t remove disc.

The cause is that more than 10 minutes has

✔

HD Radio tuner is connected to KCA-S210A or

other units.

✔

elapsed since the vehicle ACC switch was turned

OFF.

☞

Connect the HD Radio tuner directly to the

control unit.

☞

The disc can only be removed within 10

minutes of the ACC switch being turned OFF.

If more than 10 minutes has elapsed, turn

the ACC switch ON again and press the Eject

button.

? The disc won’t insert.

There’s already another disc inserted.

Press the [0] button and remove the disc.

✔

☞

English

Troubleshooting Guide

Hold Error:

The protective circuit in the unit activates

when the temperature inside the

automatic disc changer exceeds 60°C

(140°F), stopping all operation.

➪ Cool down the unit by opening

the windows or turning on the air

conditioner. As the temperature falls

below 60°C (140°F), the disc will start

playing again.

The messages shown below display your

systems condition.

Eject:

No disc magazine has been loaded in

the changer. The disc magazine is not

completely loaded.

➪ Load the disc magazine properly.

No CD in the unit.

➪ Insert the CD.

No Name:

Load:

Attempted to display DNPS during the CD

play having no disc names preset.

No Disc:

No disc has been loaded in the disc

magazine.

➪ Load a disc into the disc magazine.

Discs are being exchanged in the Disc

changer.

TOC Error:

No disc has been loaded in the disc

magazine.

➪ Load a disc into the disc magazine.

The CD is quite dirty. The CD is upside-

down. The CD is scratched a lot.

➪ Clean the CD and load it correctly.

READING:

IN (Blink):

The unit is reading the data on the disc.

The CD player section is not operating

properly.

➪ Reinsert the CD. If the CD cannot be

ejected or the display continues to flash

even when the CD has been properly

reinserted, please switch off the power

and consult your nearest service center.

E-05:

The CD is upside-down.

➪ Load the CD correctly.

Blank Disc:

Nothing has been recorded on the MD.

Unsupported File:

An Audio file is played with a format that

No Track Disc: No tracks are recorded on the MD,

although it has a title.

this unit can’t support.

➪ ----

E-15:

Media was played that doesn’t have data

recorded that the unit can play.

➪ Use media that has data recorded that

the unit can play.

Copy Protection:

A copy-protected file is played.

➪ ----

No Music Data: Media was played that doesn’t have data

recorded that the unit can play.

DEMO:

The Demonstration mode has been

selected.

➪ The <Demonstration mode Setting>

(page 35) is ON. Turn it OFF.

➪ Use media that has data recorded that

the unit can play.

Files for picture downloading only are

recorded in CD-R/CD-RW.

PROTECT:

The speaker wire has a short-circuit or

touches the chassis of the vehicle, and

then the protection function is activated.

➪ Wire or insulate the speaker cable

properly and press the reset button.

No Panel:

E-77:

The faceplate of the slave unit being

connected to this unit has been removed.

➪ Replace it.

The unit is malfunctioning for some reason.

➪ Press the reset button on the unit. If the

"E-77" code does not disappear, consult

your nearest service center.

Mecha Error: Something is wrong with the disc

magazine. Or the unit is malfunctioning for

some reason.

➪ Check the disc magazine. And then

press the reset button on the unit. If the

"Mecha Error" code does not disappear,

consult your nearest service center.

English

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (200 kHz space)

: 87.9 MHz – 107.9 MHz

Maximum output power

: 50 W x 4

Usable sensitivity (S/N = 30dB)

: 9.3dBf (0.8 μV/75 Ω)

Full Bandwidth Power (at less than 1% THD)

: 22 W x 4

Quieting Sensitivity (S/N = 50dB)

: 15.2dBf (1.6 μV/75 Ω)

Tone action

Bass : 100 Hz 8 dB

Frequency response ( 3.0 dB)

Middle : 1 kHz 8 dB

Treble : 10 kHz 8 dB

Preout level / Load (during disc play)

: 5000 mV/10 kΩ

Preout impedance

: ≤ 80 Ω

: 30 Hz – 15 kHz

Signal to Noise ratio (MONO)

: 70 dB

Selectivity ( 400 kHz)

: ≥ 80 dB

Stereo separation (1 kHz)

: 40 dB

Auxiliary input

Frequency response ( 1 dB)

: 20 Hz – 20 kHz

Input Maximum Voltage

: 1200 mV

Input Impedance

: 100 kΩ

AM tuner section

Frequency range (10 kHz space)

: 530 kHz – 1700 kHz

Usable sensitivity (S/N = 20dB)

: 28 dBµ (25 µV)

CD player section

General

Laser diode

: GaAlAs

Digital filter (D/A)

: 8 Times Over Sampling

D/A Converter

: 1 Bit

Spindle speed (Audio file)

: 1000 – 400 rpm (CLV 2times)

Operating voltage (11 – 16V allowable)

: 14.4 V

Current consumption

: 10 A

Installation Size (W x H x D)

: 182 x 53 x 162 mm

7-3/16 x 2-1/16 x 6-1/10 inch

Weight

3.09 lbs (1.40 kg)

Wow & Flutter

: Below Measurable Limit

Frequency response ( 1 dB)

: 10 Hz – 20 kHz

Total harmonic distortion (1 kHz)

: 0.008 %

Signal to Noise ratio (1 kHz)

: 110 dB

Dynamic range

: 93 dB

Channel separation

: 96 dB

MP3 decode

: Compliant with MPEG-1/2 Audio Layer-3

WMA decode

: Compliant with Windows Media Audio

AAC decode

: AAC-LC ".m4a" files

English

Motorola MOTORAZR V9 User Manual
Magic Chef MCCM1TW12 User Manual
Linear 1092 07 User Manual
Kenwood KDC MP438U User Manual
Kenwood KDC 316S User Manual
Hamilton Beach 47535C User Manual
Cuisinart Coffeemaker CBC 1600 User Manual
Centon electronic DataStick Bolt 2GBDSB BLUE User Manual
Bunn Coffeemaker CDS 3 User Manual
ABB ACS580 0P User Manual